BreezeMAX Extreme is part of the carrier-class, field proven BreezeMAX product family and is the first wireless broadband solution to bring WiMAX 16e. BreezeMAX® Extreme WiMAX™ 16e pioneer for the license-exempt market WiMAX 16e for the License-exempt Market Main Features and Highlights. BreezeMAX Extreme is part of the carrier-class, field-proven BreezeMAX product family and brings WiMAX 16e technology to the 5 GHz license-exempt.

Author: Gorg Jur
Country: Morocco
Language: English (Spanish)
Genre: Video
Published (Last): 1 August 2004
Pages: 248
PDF File Size: 3.4 Mb
ePub File Size: 14.41 Mb
ISBN: 939-5-33725-301-6
Downloads: 16395
Price: Free* [*Free Regsitration Required]
Uploader: Zujar

Cable to mains is NOT included and should be ordered separately.

Cases in which the CPE is presented as linked, even though it is not. The situation is auto recoverable and service is restored after few seconds. When operating with DHCP option 66 and 67, the CPE might not receive an IP if option 67 is not used only 66 or if the option 67 xml file is not at the specified location. CS to ensure management of the bridged BTS b. In case of using country code with DFS: When using forwarding with option 82, if the Service Group gateway is a Cisco router the following configuration must be add on the Cisco to permit the DHCP packets to pass: Software version integrity on the BTS solved starting with upgrade to version 1.

Define new service interface as Eth. It’s a community-based project which helps to repair anything. Upgrade also the CPE breezeamx Release 1.


Rocket M5 vs Alvarion BreezeMAX Extreme 5000

When upgrading to release 1. Due to FCC regulation requirements, starting with release extrene. When running Spectrum Analyzer while operating in dual sector mode, if system had developed misssynchronization because of GPS holdover, at the end of the scan process the system would reinitialize both channels.

Under GPS chaining, when 55000 is a faulty chaining cable, the radio units in the chain may not initiate transmission. Base Station ID configured in each channel must be unique in the entire network.

After switching between Operation Modes e. The following is a general description: The information is not submitted through the TR protocol.

BreezeMAX Extreme | WiMAX technology 5 GHz license-exempt solution

Please note that applying factory defaults will not change Country Code selection. No disclosure thereof shall be extremf to third parties without the express written permission of Alvarion. Radiator verified with version 4. The Ethernet port supports only Auto Negotiation mode. Specifically breezmax operating a dual-carrier BTS e. When connection with AAA is reestablished the entire cell will be authenticated again automatic de-registration of all CPE.

CSassociate to it the forwarding rule you’ve created in step ‘b’.

BreezeMAX® Extreme (BreezeMAX Extreme ) |

It corresponds to software versions: Known Issues and Limitations With Release 1. Each manual covers all relevant topics associated with the respective equipment, including: The GPS synchronization may take up to 30min when installing the base station in a new location, installer may refer to the GPS Menus as detailed in the system manual 5.

This is mainly since IP address Under dual sector SISO base-station, running a spectrum analyzer on one sector may lead as part of the scanning to BTS restart affecting the operation of the second sector. When the sum of all provisioned services exceeds the CPE license capacity, the NE process will not be completed. Multi-host support behind a single CPE might not work. Software is downloaded to the unit b.


BreezeMAX ® Extreme 5000

Such cases might occur when using limited license CPEs and the total number of services defined for such a CPE is rxtreme the licensed value.

The CPE will provision the services according to the order in which they are received until the license is exceeded. Ping messages of bytes transmitted over R1 to the host behind CPE are sometimes unanswered.

When performing backhauling over Extreme CPE i. As part of these changes, several additional configuration options are available, such as: Note that these can be overcome with additional scripts and configuration of the default installed Radiator AAA: Please note, when downgrading from Release 1.

In order to downgrade to release 1.

If static routes are added to a device acting as DHCP client the routed classes will not perform traffic. Upon successful completion the unit set automatically “run from shadow” and performs reset itself. The documentation includes the following: